Description 描述

THYOSIL E1596 is an acrylic emulsion polymer recommended for manufacturing of interior enamels and wood coatings.

是丙烯酸類乳液聚合物，推薦用于配制室內瓷漆和木器漆。

Advantages 優勢

ü Excellent adhesion to the substrate.優異的附著力

ü Low Grain Raise低晶粒提升

ü Low Odour 低氣味

ü Non-Flammable 非易燃

ü Excellent Flow and Levelling 優異的流平性

ü Outstanding UV Resistance 突出的抗紫外線特性

ü Very good gloss 非常好的光澤

ü Excellent hardness and chemical resistance卓越的硬度和耐化學腐蝕性能

Typical properties 典型值

 These properties are typical, do not constitute specifications

Starting formulations using THYOSIL E1596應用基礎配方

 *Ammonia solution of resin THYON PH725 (31.5%)

Application 應用 

·  A smooth surface is obtained by sanding the wood with #150-320 grit sandpaper. 用# 150 - 320砂紙把木頭的表面打磨光滑。

·  A first layer of sealer is required. We suggest a sealant based THYOSIL E1594. 第一層底漆，我們推薦用E1594

·  Let dry the sealant for 20 minutes, sand the surface with #320 grit sandpaper. 讓底漆干 20分鐘后，用 #320砂紙 然后再使用# 320砂紙打磨。

·  Allow the layer to dry 2 hours before re-coating.

·  預涂的底漆干后2小時后再上一次漆

·  When the previous coat has dried, recoat with another layer.

·  當先前的涂層干后再涂另一層。

·  A minimum of two coats is suggested; allow the coating to dry 24 hours before use. It is recommended to wait 7 days before performing the quality tests.建議至少涂2遍，在使用之前需干燥24小時以上。建議7天后測試性能品質。

Formulation tips 配方技巧

? Coalescent and Co-solvet effects:成膜助劑（聚結劑）和成膜溶劑的作用

 The type and level of coalescent in the formulation is critical to the balance of properties.

 成膜助劑（聚結劑）的類型和添加量的在配方中對性能的好壞是至關重要的。

? Wetting and dispersing agents: Like coalescents, the type and level of dispersant will influence the property balance of enamels and wood coatings based on THYOSIL E1596 resin. 潤濕分散劑的不同型號的選取將影響瓷漆在木器上的特性

? Defoamers消泡劑: Foam control is a major concern in waterborne coating formulation design. Additives are necessary to eliminate foam during manufacture and on application. The choice of defoamer type and level will depend primarily on the formulation and mode of application. Deeptone formulations for airless spray application, which use predispersed colorants, will require the most potent defoamer package. Brushing formulations with in-house, factory-dispersed dry pigments will require less.

A good start in choosing the right defoamer package is to have a silicone type in the grind followed by a nonsilicone in the letdown. Effectiveness of the defoamer can be screened by the shaker test, but the best candidates should be checked by actual application.

Drawdowns should also be done to check for surface defects and impact on gloss. Defoamer persistence should be checked by oven aging and retesting the defoaming capabilities.

泡沫控制是水性涂料配方設計中的主要問題。助劑是需要在生產和應用消除氣泡的。消泡劑的型號和添加量的選擇取決于配方和使用方式。無氣噴涂施工的深色調配方，它使用預分散的著色劑，消泡劑包將需要最有力的。室內刷涂的配方，工廠干顏料分散將需要較少的消泡劑。

在選擇合適的消泡劑包是一個良好的開端，硅研磨，然后由非硅調漆。的消泡劑的有效性可以通過振動試驗篩選，但實際應用中，應檢查的最佳的方案。

施工時也應做檢查表面缺陷和對光澤度的影響。消泡劑的持久性，應檢查烘箱老化和復驗的消泡能力。

Safe handling Information

Before using this product, read carefully the Material Safety Data Sheet (MSDS).

Important: Avoid freezing. 注意：避免冷凍。

Note: The statements above are based on the current state of knowledge. They are intended to describe the product in relation to necessary safety precautions, and should not be used as a warranty of any specific property. Revision: September 2013.